Showing posts with label Observed Trials. Show all posts
Showing posts with label Observed Trials. Show all posts

Monday, September 10, 2007

2007 CATRA Vintage Trial - Part 2

After the first loop I had a solid lock on fourth place (out of four). Luckily some of my competition ran into problems. (Sponge) Bob, riding a borrowed Model 92 Bultaco Sherpa T, dropped out due to a bad condenser causing the bike to lose spark. Kevin, riding an Ossa, lost spark in Section 1 during the second loop. He was able to get his bike running again, but dropped out half-way through his second loop due to heat exhaustion. It was 90+ degrees with 90% humidity that day. Can you say hot and sticky? I kept my bike running, despite being jetted way too rich for the conditions. The cylinder loaded up a couple times and I had to change out the sparkplug twice, but I rode all three loops and wound up snagging some hardware for second place in Twin-Shock Intermediate. Another guy was shooting video and he followed me around on my last loop, when I crashed twice. I'm sure some of those clips will end up on youtube.

More phots from the CATRA Vintage Trial.


"Catching Z's."
Here's 1/4 of my pit crew hard at work. My youngest son had to take a nap due to all the excitement of watching daddy ride... yeah, right?


"Stay to the right, then go left, then right around the tree. Sounds easy, no?"
Entering Section 8. The guy on the left, in the yellow t-shirt, is the observer. He's holding up a clenched fist signalling that I haven't dabbed... yet. I think the other guy is holding onto the observer to keep him from falling over with laughter. He should've been helping me.



"Hey, I made that tricky turn. Don't dab now... of shhhiii!"
Riding through Section 8.



"Close the door fool. What's a girl gotta do to get any privacy?"
My daughter refused to use the portacans, so she had her own private bathroom in the back of the van. Spoiled much?

2007 CATRA Vintage Trial - Part 1

On August 25th 2007 I competed in the CATRA Vintage Trial. Originally I signed up for Twin-Shock Novice, but I was the only one in that class. So I ended up riding Twin-Shock Intermediate with three other riders. Rarely does anyone take many photos of me while I'm riding, but on this day my wife and kids were there to cheer me on. My wife isn't used to taking action photos, so they're not the greatest. At least she didn't take any photos of me laying on the ground.

The following photos were taken in Section 1.


"I sure hope my brakes are working!"
Getting ready to drop down the hill into Section 1.



"Okay, where's that line I picked out earlier?"
Riding through Section 1. The guy behind me is Paul. He snagged first place in Twin-Shock Intermediate. I dropped more points the first loop than he did all day.


"Weight the outside peg, lean, turn... I SAID TURN!"
Still riding through Section 1.



"Whoa, check it out, you can slip a dollar bill underneath my front tire!"
Catching "BIG AIR" on the exit of Section 1.



"Yummy!"
My daughter was more interested in her ham sammich than watching daddy ride. Can't say I blame her.

Friday, September 7, 2007

Trials


1973 Bultaco Model 98 "Sherpina" left side. Restored from the ground up now sporting a Sherpa T "slimline" tank and seat.

Around five years ago I acquired and old Bultaco Model 98 Alpina. It was complete, but in pretty rough shape. My original intention was to get it in running condition and ride it in the 2003 ISDT Reuinion Ride over in Massachussetts. Well it was in worse shape than I expected and ended up doing a complete frame-up restoration including a complete engine rebuild. I was unable to get it running in time for the ISDTRR. It took me another year to complete the restoration and cost me three times what I originally budgeted for the project. Many thanks goes out to Bob Hogan, of Hogan's Cycle Shop, whom I spoke to at the 2003 ISDTRR. It was through Bob that I found out my Alpina was not a 175cc as the Model 98 was originally built. It seems that back in '73 there wasn't a class for 175cc motorcycles, so most of them had a 250 cylinder and piston installed by the importer. The entire rebuild was a learning process. I also found out it is possible to install one gear backwards causing the bike to only have three gears; first, second and third. Almost every Bultaco "expert" on the internet swears this is not possible, but I know for a fact it is.

I finished the Alpina in time to participate in the 2004 Spanish Motorcycle Owners Group (SMOG) East Trail Ride. Then it sat in my garage, collecting dust. I pulled it out for two more SMOG Rides, but following the '06 SMOG Ride I decided to turn it into a vintage trials bike. Over the winter of '06/'07 I dumped a couple hundred more into it. You can see the end result in the photos. While I still haven't totalled all the receipts, I'd estimate I have around $1000 and countless hours of labor into this bike.


1973 Bultaco Model 98 "Sherpina" right side. A sharp eye will pick out the brake and shifter are on the "wrong" sides. It wasn't until 1975 when motorcycle controls were standardized world-wide to a left side-shift, right side brake.

The Bultaco Alpina was originally patterned after their Sherpa T trials bike. The Alpina and Sherpa T basically share the same components. There are, however, a few differences. Obviously the color is different as the early Sherpa T's were red and the Alpina was blue. The gas tank is different with the Sherpa T using a slimmer profile one-gallon (slimline) tank. The Sherpa T also uses a much smaller seat since trials riding is done from standing on the pegs. A friend of mine, Pete from Hilltop Trials, sold me an old slimline tank and seat. The tank was rough and needed some fiberglass work, sealing and painting. The fiberglass seat pan was broken, but another friend of mine, (Sponge) Bob from Burnt Hills Upholstery, made a new pan, using the seat pan from another Sherpa T as a mold, cut new foam and covered it. Internally the Sherpa T had different first and second gears inside the transmission. Since these are the gears most often used when riding trials I ended up changing the final drive sprockets from 11/42 to 11/50. In retrospect I could've used an even larger rear sprocket. In the future I may try a 1-tooth smaller front sprocket. Other than that I added a set of Renthal 6-inch rise trials bars and low front fender mounting brackets.


Here I am riding the Bultaco in my second trials event, the 2007 3D Trails Club Picnic Trial in Oneonta, NY. I ended up second place in the Rookie/Vintage class that day beating out a couple modern bikes. Those guys must really suck at trials.

Since then I've competed in three trials events. On my best day I'm a mediocre novice when it comes to trials, and my results show it. I've always heard how awful Bultacos are when it comes to reliability. Frankly, most of the stuff I've had to deal with is simple and not all that uncommon for a 34 year-old machine. At my first trial, a NETA event, I ended up with a DNF when the circlip that holds the kick-start pivot to the lever came off. Turns out this is a common problem, with a common solution. Tap the end of the kick-start lever and install a bolt and washer. My second outing, a 3D Trials Club event, the bike suffered from fuel delivery problems due to a clogged fuel tap. The new ethanol-blend fuel we get here in the U.S. isn't the greatest for fiberglass fuel tanks or carburetors. So I'll have to keep an eye on this problem and regularly clean out the fuel tap. At least I was able to finish my second event.

Thursday, September 6, 2007

Introduction

Welcome to my little spot on the web where I post my reports and general blathering about my experience riding off-road (timekeeping) enduros and observed trials. Both types of competition are quite a bit different and have a unique set of rules. They require different types of motorcycles.

Enduros - An enduro is, basically, a race against the clock. The objective is to accumulate as few points as possible by maintaining a pre-set speed average. The rules are fairly complex, especially to a beginner. The promoter, usually a club, lays out a marked course over any combination of single and two-track trails, dirt and paved roads and grass or motocross tracks. A speed average, or multiple speed averages, are selected. The idea is to try and maintain the set speed average over the entire course. Groups of up to five riders are sent out on the course at one-minute intervals. Along the course there are checkpoints where your arrival time in minutes and, sometimes, seconds, is recorded. If you arrive at a checkpoint on your minute, your score is zero. For every minute late, you receive one penalty point for up to 60-minutes. Beyond 60-minutes late, you are disqualified. There are also resets where the course mileage, not ground mileage, is advanced. Therefore it is possible to get ahead of the clock. Arriving one minute early to a checkpoint results in two penalty points. For each minute early, beyond one minute, it's five penalty points up to a maximum of 15-mintes early. Beyond 15-minutes early, you are disqualified. Hence it is better to be late than early. Again this is just a brief summary of the rules.

Observed Trials - An observed trial is quite a bit different from an enduro. The object is to negotiate through a difficult section, known as a trap or observed section, without putting a foot down, called a dab. Just like an enduro, you want to accumulate as few penalty points as possible. Penalty points can only be accrued in the observed sections. One dab = one point. Two dabs = two points. Three or more dabs = three points. Falling, stalling, putting both feet on the same side of the bike = five points. The obstacles found in an observed section could be tight turns, trees, fallen logs, roots, rocks, mud, hills, or even some manmade obstacles. The important thing to remember is there are times you should take a dab in order to save yourself from getting a three or a five. Of course this is just another brief summary of the rules.